===under info was translated buy computer===
1： Unwinding part
1. Adopt two-line independent unwinding design, AC motor drive, active unwinding and large coil diameter design to reduce the number of shutdown.
2. The frequency converter controls the tension and automatically changes the speed with the change of speed and winding diameter.
3. The unwinding is equipped with an air expansion shaft, and pneumatic feeding is adopted to reduce manpower. The maximum coil weight is 120kg.
4. It is equipped with automatic shutdown device for no material and broken material.
5. Use the material roll with the edge inserted on the film blowing machine, and the raw materials can be HDPE and recycled materials.
2： Host part
Middle deviation correction part:
1. Adopt two-wire independent EPC design to guide the membrane to the correct position.
2. The two-line EPC is controlled independently and has error alarm prompt.
Printing electric eye and bag feeding part:
1. The bag has blank printing mode and color mark tracking mode.
2. The color code electric eye adopts German photoelectric eye, with zero fault and accurate sealing and cutting size.
3. The bag delivery is driven by Japan's Yaskawa servo motor, with high-speed transportation and accurate positioning.
4. Air blowing bag feeding is adopted, and the air blowing is independently controlled up and down, and the air pressure is adjusted independently.
Sealing cutter and whole book stacking device:
1. Reversible heavy-duty side sealing knife, humanized structural design, fast turnover and simple cleaning.
2. High temperature cloth has winding design, which can be wound quickly, reduce speed, waste and simple operation.
3. The temperature of the two upper and lower sealing knives is adjusted independently and controlled by an intelligent temperature controller.
4. The temperature of the intermediate cutter is adjusted independently.2
5. Automatic book fixing and stacking design.
6. The whole bag stack has a swing design, and the sealing lines of the upper and lower bags do not overlap to avoid sticking to each other.
3： Full automatic punching part
Manipulator grasping part:
1. It has bag sweeping and leveling design to make the bags stack smoothly.
2. The manipulator is controlled by AC variable-frequency motor and automatically grabs the whole bag after counting.
3. The dwell position of the manipulator is freely set according to the product size.
Automatic punching part:
1. Adopt gas-liquid booster cylinder for punching, two-line independent design, low noise and safe operation.
2. Two lines of punching die are installed independently, which can be quickly disassembled and replaced with punching tools of different sizes.
3. The bottom punching plate has the function of rotation and will not punch at the same position, saving consumption cost.
4. The punching position is freely set according to the product size.
5. The punching waste is collected centrally through the conveyor belt.
Finished product stacking collection part:
1. It has the function of folding the whole bag in half, eliminating manual folding in half.
2. Flatten the package and eliminate the air. 2.
3. Each batch of bags are automatically stacked, the collection table is automatically shifted, and the whole book is output, which is convenient for collection and packaging.
Control system:
1. The main control panel of the machine is displayed as a large screen touch screen to display various parameters in real time.
2. The whole machine has a number of automatic warning systems for safe operation, and an error warning prompt screen design.
3. The whole machine control driver is driven by PLC programmable controller.
4. 6 languages are available for the operator to choose.
Model: cw-500v2
Sealing form: double line sealing
Number of bag making rows: 2 lines
Flow direction: right to left
Discharging width: 500mm
Discharge diameter: ￠ 1000mm
Bag making width (bag width): 500mm
Bag making length (bag height): 350-700mm
Film thickness: HDPE 0.008-0.04mm
Production speed: 250pcs / min
Pulling speed: 125m / min
Total power: 19.5kw
Power supply voltage: 380V 50Hz
Machine size: 8000x2050X1800mm
Machine weight: 3300kg
Air compression: 7hp (excluding air compressor)
Working conditions:
A. The ambient light illumination shall not be greater than 3000lx
B. Altitude not exceeding 1000M
C. The temperature of surrounding medium shall not be higher than + 40 ℃ and not lower than - 20 ℃
D. The relative humidity of the air shall not be greater than 85%
E. Place without conductive dust
F. Environment without explosion hazard and close to fire source
Electrical configuration:
Name, model and brand
● pneumatic cylinder Taiwan Xingong
● solenoid valve (mindman)
● encoder 360p American rip Rep
● photoelectric eye German labor easy to measure
● touch HMI 5.7 & prime; Color Taiwan Willem ● PLC FP— Xhc60t Panasonic
● analog converter DA2 Panasonic
● rectification EPC China Ruiyu Ruiyu
● proximity switch pl-05n Taiwan Yangming
● three color warning light, petrolay, Japan
● solid state relay ssr-40da Taiwan Yangming
● intermediate relay Japan Idec
● switch button and knob Japan Idec
● air compressor pipe φ 6 、 φ 8、 φ 10 Fuji, Japan
● switching power supply 24V 100W Taiwan Delta
● control transformer 380v-220v China
● electrostatic elimination device China
● punching booster cpt-5t Taiwan kuangxin
● bag feeding servo motor 4400w, Yaskawa, Japan
● unwinding motor 550W Taiwan TCG
● unwinding frequency conversion 750W Taiwan Delta
● feeding motor 750W Taiwan TCG
● feed frequency conversion 750W Taiwan Delta
● main sealing knife drive motor 1500W Taiwan Chengbang CPG
● main sealing knife drive frequency conversion 1500W, Yaskawa, Japan
● manipulator drive motor 400W Taiwan TCG
● manipulator drive frequency conversion 400W Yaskawa, Japan
● bag sweeping motor 125w Taiwan TCG
● waste conveying motor 60W Taiwan TCG
● finished product conveying motor 60W Taiwan TCG
Cw-500v2 two-line ultra-high speed vest bag making machine (random accessories)
1. Accompanying tools (one tool box, one set of Allen wrench, one screwdriver and one cross, and one oil pot)
2. The air pipes ￠ 6 and ￠ 8 are 5m respectively.
3. Air pipe connectors -- 4 M1 / 8-6 (with adjustment), 4 M1 / 4-6 (with adjustment), 4 M1 / 4-8 (with adjustment),
Two ￠ 6y tees, two ￠ 8t tees and two M1 / 8 silencers.
4. High temperature hot cloth (without glue) 5m, high temperature adhesive tape（
25mm wide) 2 rolls.
5. Heating pipe (upper heat sealing knife ￠ 16)×580mm2 strip, lower sealing knife ￠ 10×580mm2 bar)
6. Four small proximity switches (square type) and four small relays (two four pin contacts and two pin contacts respectively, without base).
7. There are 4 hot cutting blades in the middle, and 10 lower sealing silicone rubber 2mm thick x10mm wide x580mm long.
8. 48mm×One 96mm temperature controller and two K-type thermocouples. 9. 2 switches and knobs respectively, 1 24V solenoid valve, 2 pressure regulating valves and 5 10A fuses.
10. 4 rubber pads for manipulator chuck.
11. One 60A solid state relay and one 25A solid state relay.
12. One copy of machine operation manual and one copy of circuit diagram (please correspond to the machine). Frequency converter Manual: Yaskawa brand j1000 type, provided
One copy in Chinese and one copy in English (English can be attached to the CD). 1 servo operation manual, 1 deviation correction instruction, 1 temperature controller
2 copies of instructions and 1 copy of KT5 photoelectric eye instructions.
13. Quantity of one horizontal anchor plate (without screws). (to the machine)
14. Four copper connectors for power supply.
15. One 8m-784 synchronous belt (50mm wide), three chains and one package.
16. One M12 ball joint bearing.
17. Two plastic round punching plates.
18. Two air nozzles for air expansion shaft.
10 M6 screws, 10 M8 screws, 30 M8 screws, 10 M6 screws, 10 M8 screws, 30 M8 screws, 10 M6 screws, 10 M8 screws, 30 M8 screws, 10 M6 screws, 10 M8 screws, 30 M8 screws, 10 M6 screws, 30 M8 screws, 10 M6 screws, 10 M8 screws, 10 M8 screws, 10 M8 screws, 30 M8 screws, 10 M6 screws, 30 M8 screws, 10 M6 screws, 20 M8 screws, 10 M8 screws, 10 M8 screws, 30 M8 screws, 10 M8 screws, 10 M8 screws, 10 M8 screws, 30 M8 screws, 10 M8 screws, 10 M8 screws, 20 M8 screws, 10 M8 screws, 10 M8 screws, 20 M8 screws, 10 M8 screws, 10 M8 screws, 20 M8 screws, 10.
20. 2 door lock keys and 30 plastic ties.
21. The punching tool shall be in accordance with the size specified by the customer.
22. one punching foam 1m x1m x25mm thick
contact supplier or email to admin@b2bgood.com for transport and cleanrance agent 
Click to bigger picture..
